Swiftech MCX462 Manual do Utilizador descarregar pdf

Rouchon Industries, Inc., dba Swiftech – 1703 E. 28

Street, Signal Hill, CA 90806 – Tel. 562-595-8009 – Fax 562-595-8769

E Mail: Swiftech @swiftnets.com – URL: http://www.swiftnets.com

Information subject to change without notice

Page 1

Packing list

Parts Qty Parts Qty

Heat Sink 1 Springs – pre-installed 4

Fan 1 .230x.096 Nylon spacers –

pre-installed

Fan guard 1 .220x.046 Nylon spacers

(for motherboard)

6-32 x 2” screws (for 70mm fan) 4 6-32 Hex Lock-Nuts (for

motherboard)

Push-nuts (for 80mm fan) 4 Black fiber washers (for

motherboard)

Standoffs 4 Thermal grease – Arctic

Alumina

I. Preparing the motherboard

1. You must uninstall your MB prior to installing the MCX462-U heat sink.

2. Install standoffs in MB

Determine which standoff washers to use, depending on the mounting holes sizes of your particular MB model:

• Large holes .230”(5.8mm) diameter, use in the following order: standoff, black fiber washer, .220x.046 Nylon spacers (fits

inside the MB hole), then on the other side of the MB, black fiber washer, and lock-nut.

• Small grounded holes .150”(3.8mm) diameter (you can recognize grounding by a silver ring around the holes), use in the

following order: standoff directly to the MB (black fiber washer is NOT necessary), then on the other side of the MB, black

fiber washer, and lock-nut.

• Small holes, NOT grounded (bare circuit board): you must use black fiber washers, or damage to the MB may occur: use

in the following order: standoff, black fiber washer, then on the other side of the MB, black fiber washer, and lock-nut.

MB with

large holes

MB with

small

non-grounded

holes

must use

fiber washer

MB with

small grounded

holes, no washer

necessary on

this side

Use .220x.046

nylon spacer

(fit inside the hole)

Standoff

Hex lock-nut

to back side of

the MB

Install standoff in each one of the

four holes surrounding the socket.

Keep the standoff & washer centered

over the MB holes, and secure with

hex lock nuts on backside of the

MB.

3. Re-install the MB inside the case.

II. Heat sink Installation

1. The case should be laying flat on a table.

2. Insert the processor into the socket, and lightly coat the processor core with the provided Arctic Alumina thermal compound. Only

a paper thin coat is necessary. It should be applied using preferably a razor blade, or a credit card, held between thumb and index at

a 45° angle. It is critical to ascertain that the entire core is covered with a uniform coat of thermal compound. Thermal performance will

dramatically decrease if any portion of the core is not covered by thermal compound.

1 2 3 4 5

Resumo do Conteúdo

Página 1

Página 2 - CPU core

Página 3 - Standoff

Página 4 - Nylon flat

Página 5

Mais documentos para Acessórios para Computador Swiftech MCX462

Para ver o documento Swiftech MCX462 Manual do Utilizador

Swiftech MCX462 Manual do Utilizador (2 páginas)

Comentários a estes Manuais

Sem comentários

Swiftech MCX462 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Acessórios para Computador Swiftech MCX462. Swiftech MCX462 User Manual Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Acessórios para Computador Swiftech MCX462

Comentários a estes Manuais

Manuais e produtos relacionados com Acessórios para Computador Swiftech MCX462