Swiftech H20 80 Manual do Utilizador

HH2200--8800 LLIIQQUUIIDD CCOOOOLLIINNGG KKIITTSS TUTORIAL & INSTALLATION GUIDE Thes

Figure 6a Figure 6 a shows a dual radiator setup. This particular setup was chosen to illustrate how to overcome the apparent difficulty of connecti

III. Fill and bleed operations LEAK PROOF YOUR CIRCUIT BEFORE YOU FILL IT UP – DO NOT SKIP THIS STEP! The following procedure is a convenient and

. Figure 8 . Figure 9 In the picture above, the pump is not running yet. Notice how the liquid filled-up the circuit by simple gravity Bleedin

While your pump is still running, flip your case face up as shown figure 11 for a few seconds. This will allow all the air trapped in the radiator an

VI. Available accessories Improve performance with a second radiator: MCR80-F2 Radiator assembly Part # MCR80-F2, includes radiator, 80mm fan, retent

VII. Appendix: Individual Component Installation guides - INTENTIONNALY LEFT BLANK - Rouchon Industries, Inc., dbA S

MCR80 radiator 1 80mm fan guard 1 #6 X 1 1/4” Philips screw type B 4 80x80x25mm fan 1 #6 x 3/8” Philips screw type B 4 Quick-connect fittings

Using quick-connect fittings: If you are using soft vinyl tubing, you must also use the provided tube inserts: TIP! Rubbing the extremity of the tu

1. General Use The MCP650 pump is a magnetically driven centrifugal pump featuring a 12 V DC motor. It requires no maintenance when used with de-m

Performance & Specifications Nominal voltage 12 V DC Operating voltage range 6 to 14 VDC Nominal power (@ 12 V) 24 W Nominal current (@ 12

Packing List Check-marked for applicable model and content Intel Pentium 3 Socket 370, AMD Duron, Athlon, MP, XP socket 462 Intel Xeon Proces

6. MCP650 – Exploded view Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562)

Parts list Parts QTY PARTS QTY MCW6000-P™ water-block 1 Retention clips 2 Worm drive clamps 2 SP4 hold-down plate 1 1. Preparing your Motherb

Water-block installation: Step 1 Step 2 Step 3 Center the water-block inside the retention frame. Put both clips in place for the next ste

Parts list Parts QTY PARTS QTY MCW6000-PX™ water-block 1 6-32 x 1 ¼” Philips screws 4 Worm drive clamps 2 Springs 4 SP4 hold-down plate 1 S

ASSEMBLY USING PLASTICFRAME AND SPRING CLIPSINCLUDED WITH MOTHERBOARD16 PART NO. DESCRIPTION1DUAL-XEON-BOARD Motherboard2 RETENTION Plastic retention

 Using the spring-loaded screws and standoffs included with the water-block (fig. 1), or  Using the plastic retention frames and spring slips inc

Parts QTY PARTS QTY MCW6000-NX™ water-block 1 6-32 x 7/8” Philips screws 4 Worm drive clamps 2 .600 x .250 Nylon spacer 4 SP4 hold-down plate

1. Preparing your Motherboard a. Remove the existing heat sink b. Carefully clean the CPU. c. Lightly coat the CPU with thermal compound. We recommend

Parts list Parts QTY PARTS QTY MCW6000-P™ water-block 1 3T spring/clip assemblies 2 Worm drive clamps 2 SK7 hold-down plate 1 This product i

1. Preparing your Motherboard a. Remove the existing heat sink b. Carefully clean the CPU. c. Lightly coat the CPU with thermal compound. We recommen

TTaabbllee ooff ccoonntteennttss I. TUBE ROUTING ...

Place the MCW6000-A over the CPU as shown in figure 1 page 1. The water-block step side MUST be located over the socket cam box. A label affixed

Parts QTY PARTS QTY MCW6000™ water-block 1 Spring loaded screw assemblies 2 Worm drive clamps 2 Sk8 hold-down plate 1 This product is inten

2. Water-block orientation For ease of operations during bleeding, the outlet should always be at the highest point (while system is standing upright

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

Common parts to both platforms Intel platform specific parts AMD platforms specific parts Part Qty Part Qty Part Qty MCW20 ™ assembly 1 Neo

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

6. FINAL INSPECTION:...

Preamble Congratulations on your purchase of a Swiftech liquid cooling system! This kit has been designed to facilitate the installation of the com

I. TUBE ROUTING The following table contains examples on how to establish connections between the different elements of a cooling circuit based on mu

II. Installation of the cooling components The following is a typical sequence of components installation. Placement of the cooling components may v

3. Cutting Tube lengths, and installing the tubing In order to better estimate the appropriate tube lengths between each device, it is necessary to t

Figure 6 Figure 6 above illustrates a final installation, showing the MCR80-F2 radiator in place, the MCW6000 CPU cooler, the MCW50 VGA cooler, the M